The 30-Pin ESP32 with USB-C: Still the Best First Board for Wearables
Every few months someone asks me whether they should skip the classic ESP32 and jump straight to something newer. It is a fair question, because there are lots of exciting chips out there now. But when a student or a customer tells me they want to build their first wearable, the board I still reach for is the 30-pin ESP32 development board. And now that it comes with a USB-C port, there is even less reason to hesitate.
What you get
The ESP32 Development Board 30-Pin (USB-C) is built around the WROOM-32 module. That gives you a dual-core processor, WiFi, Bluetooth, and a generous set of pins, all on a board that sits happily on a breadboard. It is priced at $14.95 CAD, and it ships from Canada with a free pin-out card (while stocks last), which I will come back to in a moment.
The USB-C connector matters more than it sounds. Micro-USB ports are fragile, and cables are easy to lose in a drawer of mystery cords. A USB-C port is sturdier, the cable goes in either way up, and nearly everyone already owns a cable that works. For a classroom or a workshop, that is one less thing that goes wrong.
Why it suits wearables
A wearable project usually needs a few specific things: a way to read a sensor or a fabric switch, a way to drive some lights or a display, and ideally a way to talk to your phone. The ESP32 covers all three. It has capacitive touch inputs, which means you can build a soft button out of conductive fabric without any extra parts. It has plenty of pins for NeoPixels and I2C screens such as an OLED. And Bluetooth LE means a phone can send it messages or change an animation.
The 30-pin format is also forgiving to prototype with. The pins are spaced for a standard breadboard, so you can test an idea in minutes with jumper wires or alligator clips before you commit to any sewing or soldering. Once the circuit works, you can move the board into a small pouch or onto a flat base and connect it to your garment.
Choosing pins that behave
This is where most beginners lose an hour, and it is the reason I made Episode 6 of the Foundations series. The ESP32 pinout looks friendly, but a few pins have special jobs. Here is the short version I give my students:
- Pins 34, 35, 36 and 39 are input only. They are fine for reading a sensor, but they cannot drive an LED.
- Some pins, such as 0, 2, 5, 12 and 15, are strapping pins that the chip reads at boot. If you hold one high or low with a circuit, the board may refuse to start. They can be used, but they are not the first ones I choose.
- Analog readings on the ADC2 group of pins do not work while WiFi is running. If you need both, use the ADC1 pins instead.
If that sounds like a lot to hold in your head, that is exactly what the pin-out card is for. Keep it next to your laptop and check it before you wire anything. If you want the full walkthrough, the video explains it step by step: Why your ESP32 pinout is confusing (and how to fix it).
Here is how you would use it
Say you want a glowing cuff. Put the ESP32 on a breadboard, connect a short strip of NeoPixels to one output pin and ground, and add a button or a piece of conductive fabric to a touch pin. In PlatformIO, a minimal setup looks like this:
[env:esp32dev]
platform = espressif32
board = esp32dev
framework = arduino
monitor_speed = 115200
From there, you can add a library, upload over USB-C, and watch the serial monitor to confirm that each input is doing what you expect. If you are new to PlatformIO, my earlier videos cover the install and the first blink. Once the prototype behaves, you can decide how to make it permanent: solder wires, use conductive thread to link fabric pads, or keep the board removable so you can wash the garment.
Speaking of which, a removable brain is a habit worth building from your very first project. Put the electronics in a pouch or on snaps, and the rest of the garment stays washable.
Which board for which person?
If you want the smallest possible footprint, a tiny board like the ESP32-C3 SuperMini is a great choice. If you want to sew the board in directly, a sewable option exists too. But if you are learning, teaching, or building something with several parts, the 30-pin board is the one I recommend. It is easy to find tutorials for, easy to breadboard, and it has the most pins to experiment with. When you outgrow it, everything you learned moves straight over to the smaller boards.
You can find it here: ESP32 Development Board 30-Pin (USB-C). If you want a project to go with it, pick up a half-size breadboard and a strip of NeoPixels, and you will have an evening of experiments ahead of you.
As always, tell me what you build. I read every comment, and your questions often turn into the next video.
Christine