A Wearable Simon Game You Can Actually Play: Inside the Video Kit
Most wearable projects are things you look at. This one is something you play. The Wearable Simon Game is a memory game that lives on your wrist: lights flash a pattern, you repeat it by tapping strips of conductive fabric, and the pattern gets longer until you slip up. I built it on a flight so I would have something to do while we waited to take off, and it turned out to be one of the most fun builds on the channel. This post walks through how it works and what is in the video kit, so you can decide whether it is the right next project for you.
How the game works
There are only three jobs in this circuit. The touch strips are your buttons. The LED pixels are your display. The ESP32 is the brain that remembers the pattern and checks what you did.
The buttons are strips of conductive fabric with a stripe pattern, which means each stripe can act as a separate touch area on one piece of cloth. When your finger touches a strip, the ESP32 notices the change and counts it as a press. There is no switch to wear out and nothing that clicks, which is exactly why fabric buttons suit clothing so well.
The lights are five addressable WS2812B pixels. They flash the pattern you need to copy, and in this build they also show your score in binary. If binary is new to you, it is a lovely way to sneak a little computer science into a project: five lights give you a top score of 31, and the build is a very concrete way to see why.
Why neoprene is the base
In the video I sew everything onto neoprene. It is soft against the skin, it is thick enough to hold the components without them poking through, and it does not fray when you cut it to fit your wrist. Whatever you choose to sew onto, cut it large enough to wrap around the place you plan to wear it, and leave room for the battery and the on/off switch.
Conductive thread and the little details
The circuit is sewn with stainless steel conductive thread. I choose steel over silver because silver thread has a tendency to tarnish, and once it does your circuit slowly loses conductivity. Clear thread holds the components in place first, so you do not see any stitching, and then the conductive thread makes the real connections. A small pair of scissors is worth having on hand, because steel thread will not be cut by a fingernail.
The pixels in the kit are sewable, with tabs you can stitch through or solder to. That flexibility is useful: if you are comfortable soldering, a few quick joints will do; if you would rather sew, the tabs are ready for it.
What is in the Wearable Simon Game Video Kit
The idea behind the video kits is that you should not have to hunt down every part. The Wearable Simon Game Video Kit includes:
- An ESP32 development board, 30-pin with USB-C
- A 5-pack of RGB LED button chips (addressable WS2812B pixels)
- Striped conductive fabric for the touch strips
- A sewable slide switch
- Soft silicone wire, 24 AWG, in mixed colours
- Electro Loops ring terminals, 15-pack
- A USB-C lithium battery charging board
- Neoprene base fabric, 30 x 20 cm
- Stainless steel 2-ply conductive thread, 25 m
- A sewing needle and needle threader
You will need to bring a soldering iron, a USB-C data cable and a small LiPo battery. About the cable: many USB-C cables only charge, and a charge-only cable will not program the ESP32, so check that yours carries data before you assume something is wrong with the board.
A note on the striped fabric
The striped conductive fabric in this kit is a specialist piece that is not sold on its own, and the kit is limited because of it. When the fabric runs out, the kit goes with it, unless I can find a reliable source. If you like the idea of the game but the kit is gone by the time you read this, you can make the same thing by cutting plain conductive fabric into strips and sewing them to a base fabric. The video shows that option too.
Is it the right project for you?
This is a level 3 build, which means it asks for both soldering and sewing. It is not a first project, but it is a very good second or third one. If you have already made a soft touch button and lit a few pixels, this is the step where those two ideas combine into something that feels like a finished object. If you are still new to the ESP32, start with the pin guide first, then come back.
The code is free on GitHub, so you can read it before you buy anything: github.com/cmoz/SimonMemoryWearableWoop. Once the game works, change it. Swap the colours, add a sixth strip, make the pattern faster, or turn the score display into something that suits your outfit.
Watch the build
The full build, including my very modest high score, is in the video: I Built a Wearable Simon Game (It Actually Works). Watch it once through before you start, then keep it open while you sew.
If you make one, tell me your high score. Mine is not high, so you will probably beat it.
Christine