How to Read a Conductive Fabric Spec: Ohms per Square, dB and GHz Explained

How to Read a Conductive Fabric Spec: Ohms per Square, dB and GHz Explained

Shopping for conductive fabric can feel like reading a lab report. One listing says 70 to 90 dB. Another says 95 dB up to 38 GHz. Another gives a resistance in ohms per square. What do these numbers actually tell you, and which ones should you care about for your project?

Here is a plain-language guide, from someone who has spent a lot of years explaining this to students.

1. Surface resistance (ohms per square)

This tells you how easily electricity travels across the fabric's surface. Lower numbers mean better conductivity.

The "per square" part confuses everyone, so here is the trick: any square of the fabric has the same resistance from one edge to the opposite edge, whether it is 1 cm across or 1 metre across. A bigger square has a longer path, but also a wider one, and the two cancel out. So ohms per square lets you compare fabrics fairly, whatever size the sample was.

What it means for you:

  • Touch buttons and sensors: almost any conductive fabric works, because the ESP32 is sensing a change in capacitance, not pushing current through the fabric. Choose for feel and look.
  • Soft circuit traces and switches: lower resistance matters more, especially over longer distances or when powering LEDs.
  • Stretch fabrics: resistance usually changes as the fabric stretches. That is a problem for a trace, but it is exactly what makes a stretch sensor work.

2. Shielding in dB

Shielding effectiveness is given in decibels, and decibels are logarithmic, which is why the numbers look small but are not. Every 10 dB means ten times less signal power gets through:

  • 10 dB: one tenth gets through
  • 30 dB: one thousandth
  • 60 dB: one millionth
  • 90 dB: one billionth

So a fabric rated 70 to 90 dB, like our Copper Ripstop Conductive Fabric (diamond pattern), blocks a huge share of the signal in the test. Our Faraday Copper Conductive Fabric, Grey is rated 95 dB by the manufacturer.

3. Frequency range (MHz and GHz)

A shielding figure only applies to the frequencies it was tested across. "95 dB up to 38 GHz" means the manufacturer measured it over a range topping out at 38 GHz. For reference:

  • NFC and most contactless cards: 13.56 MHz
  • Bluetooth and 2.4 GHz WiFi: 2.4 GHz
  • 5 GHz WiFi: 5 GHz
  • Mobile phone networks: from a few hundred MHz up to several GHz

4. Lab numbers vs your project

Shielding figures are measured on a flat, perfect sample. Your finished pouch, lining or panel has seams, folds and an opening, and every gap lets signal leak through. Overlap your seams, close the opening fully, and test the finished piece rather than trusting the number on its own. That is why you will see "manufacturer's figure" on some of our listings.

5. The other words in the listing

  • Plating: silver, copper, nickel or copper-nickel. Each has its own colour, feel and resistance to tarnish. I compare them in Silver vs Copper vs Nickel Conductive Fabric.
  • Ripstop: a reinforced grid or diamond weave that stops tears spreading. Great for structured pieces and panels.
  • Woven, knit and nonwoven: woven is stable, knit stretches, and nonwoven is felt-like and does not fray.
  • Anti-oxidation: a finish that slows tarnishing. Copper darkens over time, and while it usually still conducts, it changes the look. Our Anti-Oxidation Copper-Nickel Ripstop is worth a look if that matters for your design.
  • Thickness: thin fabrics (0.08 mm, for example) drape and sew easily. Thicker ones feel sturdier.

A quick test you can do at home

A multimeter will not give you a true ohms-per-square reading, but it is great for comparing. Set it to resistance, press both probes onto the fabric the same distance apart each time, and compare samples. Lower is more conductive. It is also the fastest way to check which side of a fabric is conductive.

Compare them in your hands

Numbers only tell you so much. The best way to choose is to feel, cut and test a few. The BIG 10: 10 x 10 cm conductive fabric samples gives you ten to compare, and if shielding is your goal, What Is EMI Shielding Fabric? is a good next read.

Christine

Back to blog

Leave a comment